Simulating planetary wave propagation to the upper atmosphere during stratospheric warming events at different mountain wave scenarios

Parameterization schemes of atmospheric normal modes (NMs) and orographic gravity waves (OGWs) have been implemented into the mechanistic Middle and Upper Atmosphere Model (MUAM) simulating atmospheric general circulation. Based on the 12-members ensemble of runs with the MUAM, a composite of the stratospheric warming (SW) has been constructed using the UK Met Office data as the lower boundary conditions. The simulation results show that OGW amplitudes increase at altitudes above 30 km in the Northern Hemisphere after the SW event. At altitudes of about 50 km, OGWs have largest amplitudes over North American and European mountain systems before and during the composite SW, and over Himalayas after the SW. Simulations demonstrate substantial (up to 50–70%) variations of amplitudes of stationary planetary waves (PWs) during and after the SW in the mesosphere-lower thermosphere of the Northern Hemisphere. Westward travelling NMs have amplitude maxima not only in the Northern, but also in the Southern Hemisphere, where these modes have waveguides in the middle and upper atmosphere. Simulated variations of PW and NM amplitudes correspond to changes in the mean zonal wind, EP-fluxes and wave refractive index at different phases of the composite SW events. Inclusion of the parameterization of OGW effects leads to decreases in amplitudes (up to 15%) of almost all SPWs before and after the SW event and their increase (up to 40–60%) after the SW in the stratosphere and mesosphere at middle and high northern latitudes. It is suggested that observed changes in NM amplitudes in the Southern Hemisphere during SW could be caused by divergence of increased southward EP-flux. This EP-flux increases due to OGW drag before SW and extends into the Southern Hemisphere.     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

基于双环滑模控制的直/气复合控制系统设计

直/气复合控制导弹具有强干扰、强非线性以及强耦合等特点，传统的姿态控制器难以适用于该种复杂干扰并存的情况，文章提出了基于双环滑模控制的直/气复合控制器。首先采用有限时间收敛趋近律分别构造内外环滑模控制器，并将角速度回路的滑模变量量化为直接力指令，以解决空气舵与姿控发动机之间的耦合问题。接着使用非线性扩张状态观测器估计综合干扰，从而设计控制器补偿侧向喷流干扰及模型不确定性等综合干扰的影响。然后基于李雅普诺夫方法证明了控制系统闭环稳定，分析了干扰补偿对控制器收敛域的影响。最后仿真结果表明，该方法跟踪速度快，动态过程平稳，具有较强的干扰抑制能力，具有很强的鲁棒性。     

直升机新型旋翼翼型气动特性与布局分析

利用结构网格计算流体力学(Computational fluid dynamics ,CFD)的翼型气动特性分析方法开展旋翼翼型气动特性计算。通过RAE282，NACA0012，OA212，OA207等翼型压力分布、升力和阻力等特性计算结果与试验结果的对比分析，验证了计算方法的准确性，并进一步完成了HF系列旋翼翼型的气动特性计算。基于翼型的气动特性，采用时间步进自由尾迹的旋翼气动性能分析方法开展旋翼桨叶翼型的气动布局优化设计，对悬停和前飞条件下的旋翼开展计算分析，得到两种条件下的旋翼气动特性。而后通过本文建立的优化方法开展旋翼翼型布局优化设计。     

扑旋翼飞行器气动特性分析及机翼拓扑优化设计

建立微型扑旋翼飞行器运动学模型,基于面元法研究低雷诺数下非定常场中扑旋翼飞行器的气动特性,得到机翼气动特性和一个工作周期内的最大气动载荷。建立扑旋翼飞行器机翼有限元模型,基于变密度法和独立连续映射法(Independent continuous mapping,ICM)对机翼进行静力学和动力学拓扑优化设计,通过改变机翼拓扑结构优化机翼模态频率,得到同时满足结构静力学和动力学要求的扑旋翼飞行器机翼拓扑结构。本文为扑旋翼飞行器机翼结构优化设计提供了基本思路和研究基础。     

面向空间天线的TWF复合材料性能研究

利用碳纤维三向编织物（triaxial woven fabric，TWF）作为增强材料，与柔性基体材料硅橡胶复合，制成兼具一定柔性和刚性的复合材料壳膜结构，用于卫星天线反射器，是一种新型的高精度可展开天线实现方案。采用复合材料细观方法，对碳纤维增强硅橡胶TWF复合材料进行了力学性能的研究。首先由纤维和基体的材料特性得到均质纤维束的材料特性；接下来考虑纤维束交织情况（起伏波动）建立由纤维束组成的单胞实体有限元模型；然后对单胞实体有限元模型进行均匀化分析，施加周期性边界条件，最终得到等效的均质材料特性；为满足天线反射器高性能需求，分析了碳纤维种类、纤维体积分数对单胞等效性能的影响规律。对该材料力学性能的研究，可以为其未来应用于大型高精度可展开天线反射器提供一定的理论依据。     

云制造环境下机床装备资源选择方法

针对云制造环境下机床装备资源具有数量大、异质异构、服务制约因素多等问题，提出了基于多准则决策的机床装备资源选择方法。首先，利用本体论对机床装备资源建模，将物理资源虚拟化封装，实现虚拟资源与物理资源的逻辑映射。进一步地，使用语言变量量化决策者评估信息，采用模糊决策与试验评价实验室（FDEMATEL）和熵值法（EW）相结合的组合赋权法，引入模糊VIKOR（FVIKOR）多属性决策方法对机床装备资源进行综合评估，建立FDEMATEL-EW-FVIKOR的多准则混合决策模型。最后，将该方法应用于某生产制造企业，实验对比决策结果验证了多准则混合决策模型的可行性和有效性。     

基于不确定性的飞行器分离可靠性建模与分析方法

为实现飞行器分离任务可靠性的定量分析和高效精确评估，研究了高超声速飞行器分离任务过程中各种不确定性因素对分离可靠性的影响，提出一种基于不确定性的飞行器分离可靠性建模与分析方法。面向高超声速飞行器分离任务需求，建立分离动力学仿真模型，综合考虑分离过程不确定性因素的影响，利用灵敏度分析方法识别主要不确定性因素，构建分离可靠性模型。针对此模型，提出一种改进主动学习Kriging(IAK)的分离可靠性分析方法，通过新的采样策略选取失效概率更大的采样点作为新增训练点，进行高效可靠性分析。实例结果表明，该方法能够准确描述不确定性因素对分离过程的影响，提升分离可靠性定量分析的精度和效率，为飞行器分离方案的精细化设计提供支撑。     

共轴刚性旋翼气动干扰数值计算方法

建立了一个适用于共轴刚性旋翼气动特性分析的数值模拟方法。该方法采用任意拉格朗日欧拉方法(Arbitrary Lagrange Euler,ALE)描述的可压缩Navier-Stokes(N-S)方程求解流场,采用低数值耗散的Roe格式进行空间离散;使用多重嵌套网格方法以模拟双旋翼的运动。针对共轴刚性旋翼配平,引入"差量修正"策略解决了传统配平中雅克比矩阵计算复杂的问题。首先,对Harrington-2共轴双旋翼的悬停气动性能进行了计算,然后,对某2 m直径共轴双旋翼的悬停及前飞状态进行了计算,并与试验值进行了对比。结果表明:在典型状态下拉力系数的计算结果与试验值误差在3%以内,扭矩系数的计算结果与试验值误差基本在5%以内;所采用的数值计算方法对旋翼涡尾迹特征具有较高的捕捉精度,可以有效模拟共轴刚性旋翼悬停和小速度前飞下的复杂流场及其细节特征。     

蜻蜓起飞过程飞行特征实验

针对蜻蜓自由起飞过程和准自由起飞过程进行实验观测,采用两个光轴相互垂直的高速摄像机进行拍摄,通过特征点匹配和三维重构方法准确地捕捉了两种起飞过程中蜻蜓身体和翅膀的运动参数,并进行运动特征分析与对比。实验结果表明:蜻蜓在自由起飞过程中采用同步振翅,离地后逐步转换成异步振翅(约110°),最大瞬时竖直加速度可以达到20m/s2;在准自由起飞过程中采用异步振翅(相位差180°),之后相位差逐步降低,最大瞬时竖直加速度为12m/s2;此外发现同步振翅、大攻角下拍及大拍动角有利于升力的产生。